Sen. Dan Kotowski

Filed: 4/15/2013

 

 


 

 


 
09800SB1255sam001LRB098 08773 RLC 44520 a

1
AMENDMENT TO SENATE BILL 1255

2    AMENDMENT NO. ______. Amend Senate Bill 1255 by replacing
3everything after the enacting clause with the following:
 
4    "Section 1. Short title. This Act may be cited as the
5Unsafe Handgun Act.
 
6    Section 5. Definitions. For the purposes of this Act:
7    "Department" means the Department of State Police.
8    "Director" means the Director of State Police.
9    "Firearm" has the meaning provided in Section 1.1 of the
10Firearm Owners Identification Card Act.
11    "Firing requirement for handguns" means a test fulfilling
12the requirements of Section 15 in which the manufacturer
13provides 3 handguns of the make and model for which
14certification is sought to an independent testing laboratory
15certified by the Director under Section 35.
16    "Handgun" means any firearm, including, but not limited to,

 

 

09800SB1255sam001- 2 -LRB098 08773 RLC 44520 a

1a pistol or a revolver, capable of being concealed upon the
2person.
3    "Magazine disconnect mechanism" means a mechanism that
4prevents a semiautomatic pistol that has a detachable magazine
5from operating to strike the primer of ammunition in the firing
6chamber when a detachable magazine is not inserted in the
7semiautomatic pistol.
8    "Pistol" means any handgun that is not a revolver.
9    "Revolver" means a handgun that has a rotating cylinder
10containing multiple chambers for loading and firing
11ammunition.
 
12
13    Section 10. Drop safety requirement for handguns. At the
14conclusion of the firing requirements for handguns described in
15Section 15, the same certified independent testing laboratory
16shall subject the same 3 handguns of the make and model for
17which certification is sought, to the following test:
18    (1) A primed case (no powder or projectile) shall be
19inserted into the chamber. For a pistol, the slide shall be
20released, allowing it to move forward under the impetus of the
21recoil spring, and an empty magazine shall be inserted. For
22both a pistol and a revolver, the weapon shall be placed in a
23drop fixture capable of dropping the pistol from a drop height
24of 1 meter + 1 centimeter (39.4 + 0.4 inches) onto the largest
25side of a slab of solid concrete having minimum dimensions of

 

 

09800SB1255sam001- 3 -LRB098 08773 RLC 44520 a

17.5 x 15 x 15 centimeters (3 x 6 x 6 inches). The drop distance
2shall be measured from the lowermost portion of the weapon to
3the top surface of the slab. The weapon shall be dropped from a
4fixture and not from the hand. The weapon shall be dropped in
5the condition that it would be in if it were dropped from a
6hand (cocked with no manual safety applied). If the pistol is
7designed so that upon leaving the hand a "safety" is
8automatically applied by the pistol, this feature shall not be
9defeated. An approved drop fixture is a short piece of string
10with the weapon attached at one end and the other end held in
11an air vise until the drop is initiated.
12    (2) The following 6 drops shall be performed:
13        (A) Normal firing position with barrel horizontal.
14        (B) Upside down with barrel horizontal.
15        (C) On grip with barrel vertical.
16        (D) On muzzle with barrel vertical.
17        (E) On either side with barrel horizontal.
18        (F) If there is an exposed hammer or striker, on the
19    rearmost point of that device, otherwise on the rearmost
20    point of the weapon.
21    (3) The primer shall be examined for indentations after
22each drop. If indentations are present, a fresh primed case
23shall be used for the next drop.
24    (4) The make and model of handgun shall pass this test if
25each of the 3 test guns does not fire the primer.
 

 

 

09800SB1255sam001- 4 -LRB098 08773 RLC 44520 a

1    Section 15. Firing requirement for handguns.
2    (a) The handguns of the make and model for which
3certification is sought, and which are to be tested under this
4Section, may not be refined or modified in any way from those
5that would be made available for retail sale if certification
6is granted. The magazines of a tested handgun shall be
7identical to those that would be provided with the handgun to a
8retail customer.
9    (b) The firing requirement for handguns test shall be
10conducted as follows:
11        (1) The laboratory shall fire 600 rounds from each gun,
12    stopping after each series of 50 rounds has been fired for
13    5 to 10 minutes to allow the weapon to cool, stopping after
14    each series of 100 rounds has been fired to tighten any
15    loose screws and clean the gun in accordance with the
16    manufacturer's instructions, and stopping as needed to
17    refill the empty magazine or cylinder to capacity before
18    continuing.
19        (2) The ammunition used shall be of the type
20    recommended by the handgun manufacturer in the user manual,
21    or if none is recommended, any standard ammunition of the
22    correct caliber in new condition that is commercially
23    available.
24    (c) A handgun shall pass this test if each of the 3 test
25guns meets both of the following:
26        (1) Fires the first 20 rounds without a malfunction

 

 

09800SB1255sam001- 5 -LRB098 08773 RLC 44520 a

1    that is not due to ammunition that fails to detonate.
2        (2) Fires the full 600 rounds with no more than 6
3    malfunctions that are not due to ammunition that fails to
4    detonate and without any crack or breakage of an operating
5    part of the handgun that increases the risk of injury to
6    the user.
7    (d) If a handgun fails the requirements of either paragraph
8(1) or (2) of subsection (c) of this Section due to ammunition
9that fails to detonate, the handgun shall be retested from the
10beginning of the "firing requirement for handguns" test. A new
11model of the handgun that failed the test due to ammunition
12that fails to detonate may be submitted for the test to replace
13the handgun that failed.
14    (e) As used in this Section, "malfunction" means a failure
15to properly feed, fire, or eject a round, or failure of a
16handgun to accept or eject the magazine, or failure of a
17handgun's slide to remain open after the magazine has been
18expended.
 
19    Section 20. Unsafe handguns. Any handgun is an unsafe
20handgun when any of the following is true:
21    (a) For a revolver:
22        (1) It does not have a safety device that, either
23    automatically in the case of a double-action firing
24    mechanism, or by manual operation in the case of a
25    single-action firing mechanism, causes the hammer to

 

 

09800SB1255sam001- 6 -LRB098 08773 RLC 44520 a

1    retract to a point where the firing pin does not rest upon
2    the primer of the cartridge.
3        (2) It does not meet the firing requirement for
4    handguns.
5        (3) It does not meet the drop safety requirement for
6    handguns.
7    (b) For a pistol:
8        (1) It does not have a positive manually operated
9    safety device, as determined by standards relating to
10    imported guns adopted by the federal Bureau of Alcohol,
11    Tobacco, Firearms and Explosives.
12        (2) It does not meet the firing requirement for
13    handguns.
14        (3) It does not meet the drop safety requirement for
15    handguns.
16        (4) For all center fire semiautomatic pistols, it does
17    not have a chamber load indicator and, if it has a
18    detachable magazine, a magazine disconnect mechanism.
19        (5) For all rimfire semiautomatic pistols, it does not
20    have a magazine disconnect mechanism, if it has a
21    detachable magazine.
 
22    Section 25. Penalty; exceptions.
23    (a) Commencing January 1, 2015, any person in this State
24who manufactures or causes to be manufactured, imports into the
25State for sale, keeps for sale, offers or exposes for sale,

 

 

09800SB1255sam001- 7 -LRB098 08773 RLC 44520 a

1gives, or lends any unsafe handgun shall be guilty of a petty
2offense for a first violation, a Class A misdemeanor for a
3second violation, and Class 4 felony for a third or subsequent
4violation.
5    (b) This Section shall not apply to any of the following:
6        (1) The manufacture in this State, or importation into
7    this State, of any prototype handgun, when the manufacture
8    or importation is for the sole purpose of allowing an
9    independent laboratory certified by the Department under
10    Section 35 to conduct an independent test to determine
11    whether that handgun is prohibited by this Act, and, if
12    not, allowing the Department to add the firearm to the
13    roster of handguns that may be sold in this State under
14    Section 40.
15        (2) The importation or lending of a handgun by
16    employees or authorized agents of entities determining
17    whether the weapon is prohibited by this Section.
18        (3) Firearms listed as curios or relics, as defined in
19    Section 478.11 of Title 27 of the Code of Federal
20    Regulations.
21        (4) The sale or purchase of any handgun, if the handgun
22    is sold to, or purchased by, any federal, State or local
23    law enforcement agency, any State's Attorney's office, or
24    the armed forces of this State or of the United States for
25    use in the discharge of their official duties. Nor shall
26    anything in this Section prohibit the sale to, or purchase

 

 

09800SB1255sam001- 8 -LRB098 08773 RLC 44520 a

1    by, sworn members of these agencies of any handgun.
2    (c) Violations of subsection (a) of this Section are
3cumulative with respect to each handgun and shall not be
4construed as restricting the application of any other law.
 
5    Section 30. Certification by manufacturers and sellers
6that handguns are not unsafe.
7    (a) Every person who is licensed as a manufacturer of
8firearms under Chapter 44 (commencing with Section 921) of
9Title 18 of the United States Code and who manufactures
10firearms in this State shall certify under penalty of perjury
11and any other remedy provided by law that every model, kind,
12class, style, or type of handgun that the person manufactures
13is not an unsafe handgun as prohibited by this Act.
14    (b) Every person who imports into the State for sale, keeps
15for sale, or offers or exposes for sale any handgun shall
16certify under penalty of perjury and any other remedy provided
17by law that every model, kind, class, style, or type of handgun
18that the person imports, keeps, or exposes for sale is not an
19unsafe handgun as prohibited by this Act.
 
20    Section 35. Testing requirement; certification of
21laboratories; test report.
22    (a) Any handgun manufactured in this State, imported into
23the State for sale, kept for sale, or offered or exposed for
24sale, shall be tested within a reasonable period of time by an

 

 

09800SB1255sam001- 9 -LRB098 08773 RLC 44520 a

1independent laboratory certified under subsection (b) of this
2Section to determine whether that handgun meets or exceeds the
3standards defined in Section 20.
4    (b) On or before October 1, 2014, the Department shall
5certify laboratories to verify compliance with the standards
6defined in Section 20. The Department may charge any laboratory
7that is seeking certification to test any handgun as provided
8in this Act, a fee not exceeding the costs of certification.
9    (c) The certified testing laboratory shall, at the
10manufacturer's or importer's expense, test the handgun and
11submit a copy of the final test report directly to the
12Department along with a prototype of the handgun to be retained
13by the Department. The Department shall notify the manufacturer
14or importer of its receipt of the final test report and the
15Department's determination as to whether the handgun tested may
16be sold in this State.
17    (d) No center-fire semiautomatic pistol may be submitted
18for testing as provided in this Act if it does not have a
19chamber load indicator and, if it has a detachable magazine, a
20magazine disconnect mechanism. No rimfire semiautomatic pistol
21may be submitted for testing as provided in this Act if it has
22a detachable magazine and does not have a magazine disconnect
23mechanism.
 
24    Section 40. Roster of firearms determined not to be unsafe;
25fee for maintenance of roster.

 

 

09800SB1255sam001- 10 -LRB098 08773 RLC 44520 a

1    (a) On and after January 1, 2015, the Department shall
2compile, publish, and thereafter maintain on its website a
3roster listing all of the handguns that have been tested by a
4certified testing laboratory, have been determined not to be
5unsafe handguns, and may be sold in this State under this Act.
6The roster shall list, for each handgun, the manufacturer,
7model number, and model name.
8        (b)(1) The Department may charge every person in this
9    State who is licensed as a manufacturer of firearms under
10    Chapter 44 (commencing with Section 921) of Title 18 of the
11    United States Code, and any person in this State who
12    manufactures or causes to be manufactured, imports into the
13    State for sale, keeps for sale, or offers or exposes for
14    sale any handgun in this State, an annual fee not exceeding
15    the costs of preparing, publishing, and maintaining the
16    roster under subsection (a) of this Section and the costs
17    of research and development, report analysis, firearms
18    storage, and other program infrastructure costs necessary
19    to implement this Act.
20        (2) Any handgun that is manufactured by a manufacturer
21    who manufactures or causes to be manufactured, imports into
22    the State for sale, keeps for sale, or offers or exposes
23    for sale any handgun in this State, and who fails to pay
24    any fee required under paragraph (1) of this subsection,
25    may be excluded from the roster.
26        (3) If a purchaser has initiated a transfer of a

 

 

09800SB1255sam001- 11 -LRB098 08773 RLC 44520 a

1    handgun that is listed on the roster as not unsafe, and
2    prior to the completion of the transfer, the handgun is
3    removed from the roster of not unsafe handguns because of
4    failure to pay the fee required to keep that handgun listed
5    on the roster, the handgun shall be deliverable to the
6    purchaser, if the purchaser is not otherwise prohibited
7    from purchasing or possessing the handgun. However, if a
8    purchaser has initiated a transfer of a handgun that is
9    listed on the roster as not unsafe, and prior to the
10    completion of the transfer, the handgun is removed from the
11    roster under subsection (d) of Section 45, the handgun
12    shall not be deliverable to the purchaser.
 
13    Section 45. Retesting of handguns on roster.
14    (a) The Director may annually retest up to 5 percent of the
15handgun models that are listed on the roster described in
16subsection (a) of Section 40.
17    (b) The retesting of a handgun model under subsection (a)
18of this Section shall conform to the following:
19        (1) The Director shall obtain from retail or wholesale
20    sources, or both, 3 samples of the handgun model to be
21    retested.
22        (2) The Director shall select the certified laboratory
23    to be used for the retesting.
24        (3) The ammunition used for the retesting shall be of a
25    type recommended by the manufacturer in the user manual for

 

 

09800SB1255sam001- 12 -LRB098 08773 RLC 44520 a

1    the handgun. If the user manual for the handgun model makes
2    no ammunition recommendation, the Director shall select
3    the ammunition to be used for the retesting. The ammunition
4    shall be of the proper caliber for the handgun,
5    commercially available, and in new condition.
6    (c) The retest shall be conducted in the same manner as the
7testing prescribed in Sections 10 and 15.
8    (d) If the handgun model fails retesting, the Director
9shall remove the handgun model from the roster maintained under
10subsection (a) of Section 40.
 
11    Section 50. Removal of handgun from roster.
12    (a) A handgun model removed from the roster under
13subsection (d) of Section 45 may be reinstated on the roster if
14all of the following are met:
15        (1) The manufacturer petitions the Director for
16    reinstatement of the handgun model.
17        (2) The manufacturer pays the Department for all of the
18    costs related to the reinstatement testing of the handgun
19    model, including the purchase price of the handguns, prior
20    to reinstatement testing.
21        (3) The reinstatement testing of the handguns shall be
22    in accordance with subsections (b) and (c) of Section 45.
23        (4) The 3 handgun samples shall be tested only once for
24    reinstatement. If the sample fails it may not be retested.
25        (5) If the handgun model successfully passes testing

 

 

09800SB1255sam001- 13 -LRB098 08773 RLC 44520 a

1    for reinstatement, and if the manufacturer of the handgun
2    is otherwise in compliance with this Act, the Director
3    shall reinstate the handgun model on the roster maintained
4    under subsection (a) of Section 40.
5        (6) The manufacturer shall provide the Director with
6    the complete testing history for the handgun model.
7    (b) Notwithstanding subsection (a) of Section 45, the
8Director may at any time, in his or her discretion, further
9retest any handgun model that has been reinstated to the
10roster.
 
11    Section 55. Listing of handguns differing only
12cosmetically from handguns on roster.
13    (a) A handgun shall be deemed to satisfy the requirements
14of subsection (a) of Section 40 if another handgun made by the
15same manufacturer is already listed and the unlisted handgun
16differs from the listed handgun only in one or more of the
17following features:
18        (1) Finish, including, but not limited to, bluing,
19    chrome-plating, oiling, or engraving.
20        (2) The material from which the grips are made.
21        (3) The shape or texture of the grips, so long as the
22    difference in grip shape or texture does not in any way
23    alter the dimensions, material, linkage, or functioning of
24    the magazine well, the barrel, the chamber, or any of the
25    components of the firing mechanism of the handgun.

 

 

09800SB1255sam001- 14 -LRB098 08773 RLC 44520 a

1        (4) Any other purely cosmetic feature that does not in
2    any way alter the dimensions, material, linkage, or
3    functioning of the magazine well, the barrel, the chamber,
4    or any of the components of the firing mechanism of the
5    handgun.
6    (b) Any manufacturer seeking to have a handgun listed under
7this Section shall provide to the Department all of the
8following:
9        (1) The model designation of the listed handgun.
10        (2) The model designation of each handgun that the
11    manufacturer seeks to have listed under this Section.
12        (3) A statement, under oath, that each unlisted handgun
13    for which listing is sought differs from the listed handgun
14    only in one or more of the ways identified in subsection
15    (a) of this Section and is in all other respects identical
16    to the listed handgun.
17    (c) The Department may, in its discretion and at any time,
18require a manufacturer to provide to the Department any model
19for which listing is sought under this Section, to determine
20whether the model complies with the requirements of this
21Section.
 
22    Section 60. Exceptions for certain revolvers and pistols.
23    (a) This Act shall not apply to a single-action revolver
24that has at least a 5-cartridge capacity with a barrel length
25of not less than 3 inches, and meets any of the following

 

 

09800SB1255sam001- 15 -LRB098 08773 RLC 44520 a

1specifications:
2        (1) Was originally manufactured prior to 1900 and is a
3    curio or relic, as defined in Section 478.11 of Title 27 of
4    the Code of Federal Regulations, or is a replica of such a
5    revolver.
6        (2) Has an overall length measured parallel to the
7    barrel of at least 7 and one-half inches when the handle,
8    frame or receiver, and barrel are assembled.
9        (3) Has an overall length measured parallel to the
10    barrel of at least 7 and one-half inches when the handle,
11    frame or receiver, and barrel are assembled and that is
12    currently approved for importation into the United States
13    under the provisions of paragraph (3) of subsection (d) of
14    Section 925 of Title 18 of the United States Code.
15    (b) This Act shall not apply to a single-shot pistol with a
16barrel length of not less than 6 inches and that has an overall
17length of at least 10 and one-half inches when the handle,
18frame or receiver, and barrel are assembled.
 
19    Section 65. Exception for pistols designed for Olympic
20target shooting.
21    (a) The General Assembly finds a significant public purpose
22in exempting pistols that are designed expressly for use in
23Olympic target shooting events. Therefore, those pistols that
24are sanctioned by both the International Olympic Committee and
25USA Shooting (the national governing body for international

 

 

09800SB1255sam001- 16 -LRB098 08773 RLC 44520 a

1shooting competition in the United States), that are used for
2Olympic target shooting purposes, and that fall within the
3definition of "unsafe handgun" under paragraph (3) of
4subsection (b) of Section 20 shall be exempt from the
5provisions of this Act, as provided in subsection (b) of this
6Section.
7    (b) The Department shall create a program that is
8consistent with the purpose stated in subsection (a) of this
9Section to exempt specific models of competitive firearms from
10this Act, and shall publish on its website a list of those
11specific models. The exempt competitive firearms may be based
12on recommendations by USA Shooting consistent with the
13regulations contained in the USA Shooting Official Rules or may
14be based on the recommendation or rules of any other
15organization that the Department deems relevant.
 
16    Section 70. Exception for certain sales, loans, and
17transfers. This Act shall not apply to any of the following:
18    (1) The sale, loan, or transfer of any handgun described in
19subsection (b) of Section 25, for the purposes set forth in
20that Section.
21    (2) The sale, loan, or transfer of any handgun listed as a
22curio or relic, as defined in Section 478.11 of Title 27 of the
23Code of Federal Regulations.
24    (3) The sale, loan, or transfer of any handgun that is to
25be used solely as a prop during the course of a motion picture,

 

 

09800SB1255sam001- 17 -LRB098 08773 RLC 44520 a

1television, or video production by an authorized participant
2therein in the course of making that production or event or by
3an authorized employee or agent of the entity producing that
4production or event.
5    (4) The sale, loan, or transfer of any handgun that has
6been altered to render it permanently inoperable.
 
7    Section 99. Effective date. This Act takes effect upon
8becoming law.".